Shop - Hotrod Partz

Performer Intake Manifold in Satin Finish

Add to cart

Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish

$329.95

Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish

$329.95

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347021048
Series	Performer
Grade Type	Performance
Gasket Or Seal Included	No
Vehicle Model	Chevrolet
Availability Note	Available to Order
Warranty	12 Months
RPM Range	Idle-5500 RPM
Emissions Code
Hazardous Materials Warning	WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Manifold ht: A-3.50″, B-4.60″; Carb pad height: 4.05″; Carb recommendations: OEM 4-Bbl, Use choke rod #9171. Edelbrock AVS2 Series or Performer Series Carb 500-650cfm. Bracket #8031 or #8036 for 1972-1978.; Port exit dimensions: 1.14″ x 1.88″; Recommended intake gasket: GM #10159409; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Sealant must be used on intake bolt threads if the threads extend into lifter valley or coolant passage.; NPT/Pipe thread fittings require the use of Teflon tape or paste on threads to ensure proper seal.; DO NOT OVERTIGHTEN NPT/Pipe fittings, this may cause the aluminum to crack around the fitting boss. NPT/Pipe thread is a tapered thread.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.; Choke plate #8901 included; Even though manifolds are compatible with EGR systems, this does not mean they are legal for use on emissions controlled vehicles. Check local laws for legality.; Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Color	Satin
Finish	Satin
Material	Aluminum
Rear Maximum Height	4.600 in
Single Or Dual Plane Type	Dual

SKU: Per/Per/6
Availability:
19 in stock
Category: Manifold Intake

or View Full Info

Add to cart

Performer Intake Manifold for Buick 400-455 V8, Non-EGR, Satin Finish

$440.95

Performer Intake Manifold for Buick 400-455 V8, Non-EGR, Satin Finish

$440.95

More Information
Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347021468
Series	Performer
Gasket Or Seal Included	No
Vehicle Model	Buick
Availability Note	Available to Order
Warranty	12 Months
RPM Range	Idle-5500 RPM
Emissions Code
Hazardous Materials Warning	WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Recommended intake gaskets: for 1967-71, Fel-Pro #MS96005; 1972-76, Fel-Pro #MS96014; Manifold height: A-3.80″, B-4.75″; Carb pad height: 4.27″; Carb recommendations: OEM 4-Bbl, Edelbrock AVS2 or Performer Series 650-800cfm; Port exit dimensions: 1.14″ x 2.26″; #2146 accepts divorced choke-type Quadrajet only.; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.
Finish	Satin
Material	Aluminum
Rear Maximum Height	4.750 in
Single Or Dual Plane Type	Dual

SKU: TBI/TBI
Availability:
16 in stock
Category: Manifold Intake

or View Full Info

Add to cart

Performer Intake Manifold for GM 90 Deg V6 (3.8L & 4.3L), Vortec

$402.95

Performer Intake Manifold for GM 90 Deg V6 (3.8L & 4.3L), Vortec

$402.95

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347021147
Series	Performer
Gasket Or Seal Included	No
Vehicle Model	Chevrolet
Availability Note	Available to Order
Warranty	12 Months
RPM Range	Idle-5500 RPM
Emissions Code
Hazardous Materials Warning	WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Recommended intake gasket: GM 89017866; Manifold height: A-3.50″, B-4.18″; Carb pad height: 3.84″; Carb recommendations: Edelbrock AVS2 Series or Performer Series 500cfm; Port exit dimensions: port exit is 2.05″ tall with slanted side walls; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.
Finish	Satin
Material	Aluminum
Rear Maximum Height	4.180 in
Single Or Dual Plane Type	Dual

SKU: Int/Int/Int/6
Availability:
20 in stock
Category: Manifold Intake

or View Full Info

Add to cart

Performer Intake Manifold for Olds 400-455, Non-EGR, Satin

$494.95

Performer Intake Manifold for Olds 400-455, Non-EGR, Satin

$494.95

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347021512
Series	Performer
Gasket Or Seal Included	No
Vehicle Model	Oldsmobile
Availability Note	Available to Order
Warranty	12 Months
RPM Range	Idle-5500 RPM
Emissions Code
Hazardous Materials Warning	WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	For correct gasket kit when using #2151 in a marine/ competition application, contact Mondello Performance at (805) 237-8808.; Manifold height: A-4.40″, B-5.50″; Carb pad height: 4.95″; Carb recommendations: Edelbrock AVS2 or Performer Series 750-800cfm; Port exit dimensions: 1.22″ x 2.22″; Manifold has no provision for OEM choke operation.; Will not fit Toronado or 4-4-2 Ram-Air scoop without hood modification or 1964-67 Cutlass; HEI will clear; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.
Finish	Satin
Material	Aluminum
Rear Maximum Height	5.500 in
Single Or Dual Plane Type	Dual

SKU: Int/Int/Int/3
Availability:
35 in stock
Category: Manifold Intake

or View Full Info

Performer Intake Manifold for Vortec Heads

Add to cart

Performer Intake Manifold for Small-Block Chevy w/Vortec Heads

$322.95

Performer Intake Manifold for Small-Block Chevy w/Vortec Heads

$322.95

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347021161
Series	Performer
Gasket Or Seal Included	No
Vehicle Model	Chevrolet
Availability Note	Available to Order
Warranty	12 Months
RPM Range	Idle-5500 RPM
Emissions Code
Hazardous Materials Warning	WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Recommended intake gasket: Edelbrock #7235; Manifold ht: A-3.87″, B-5.28″; Carb pad height: 4.57″; Carb recommendations: OEM 4-Bbl (pre-1981, Electric choke ONLY) Use #8032 throttle bracket. Edelbrock AVS2 Series or Performer Series 500-650cfm, use bracket #8032 for 1972-78.; Port exit dimensions: 2.05″ tall with slanted side walls; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Sealant must be used on intake bolt threads if the threads extend into lifter valley or coolant passage.; NPT/Pipe thread fittings require the use of Teflon tape or paste on threads to ensure proper seal.; DO NOT OVERTIGHTEN NPT/Pipe fittings, this may cause the aluminum to crack around the fitting boss. NPT/Pipe thread is a tapered thread.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.; Stock brackets will require modification to fit the upright manifold bolt holes.; Will not fit under stock Corvette hood.; Even though manifolds are compatible with EGR systems, this does not mean they are legal for use on emissions controlled vehicles. Check local laws for legality.; Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Finish	Satin
Material	Aluminum
Rear Maximum Height	5.280 in
Single Or Dual Plane Type	Dual

SKU: Per/Per/Per/5
Availability:
22 in stock
Category: Manifold Intake

or View Full Info

Add to cart

Performer Intake Manifold Small-Block Chevy

$381.95

Performer Intake Manifold Small-Block Chevy

$381.95

More Information
Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347037063
Series	Performer
Gasket Or Seal Included	No
Vehicle Model	Chevrolet
Availability Note	Available to Order
Warranty	12 Months
RPM Range	Idle-5500 RPM
Emissions Code
Hazardous Materials Warning	WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Manifold ht: A-3.50″, B-4.60″; Carb pad height: 4.05″; Carb recommendations: OEM 4-Bbl, Edelbrock Performer Series #1400, 600 cfm.; Port exit dimensions: 1.14″ x 1.88″; Recommended intake gasket: GM #10163409; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Sealant must be used on intake bolt threads if the threads extend into lifter valley or coolant passage.; NPT/Pipe thread fittings require the use of Teflon tape or paste on threads to ensure proper seal.; DO NOT OVERTIGHTEN NPT/Pipe fittings, this may cause the aluminum to crack around the fitting boss. NPT/Pipe thread is a tapered thread.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.; Choke plate #8901 included; See adapter #8035 for clamp-on EGR valve.; With carb #1400 & #3701, EGR spacer #1476 is required.; The #3706 has no provision for exhaust heated chokes.; Even though manifolds are compatible with EGR systems, this does not mean they are legal for use on emissions controlled vehicles. Check local laws for legality.; Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Finish	Satin
Material	Aluminum
Rear Maximum Height	4.600 in
Single Or Dual Plane Type	Dual

DOWNLO

SKU: Sma/Sma/3
Availability:
12 in stock
Category: Manifold Intake

or View Full Info