Edelbrock 1406 Performer Power Package w/Adptr, Small Block Chevy
Chevy Small Block V8, One Carburetor Quantity
- Edelbrock Performer Series 4 barrel carbs have proven themselves to be easy to tune with great drivability
- Bolt-on-and-run performance right out of the box
- For small-block Chevy engines operating from off-idle to 5500 rpm
- Smooth idling camshaft for daily drivers, trucks, vans, RVs and 4x4s
- All Edelbrock products are proudly made in the U.S.A.
Edelbrock 2101 Performer 1955-86 Small Block Chevy Intake Manifold
- Designed for street 1955-86 small block Chevys
- Stock replacement/street legal part for 302/327/350 V8s with OEM 4 bbl. or Edelbrock Performer Series carbs.
- Will also work on 1966-72 (1973 non-California) cars, 1966-83 trucks and Suburbans; except stock equipped EGR
- Performers accept late-model choke, waterneck, air-conditioning, alternator and H.E.I.
- Not for 1987 and later cast iron or Chevy Bowtie heads
- Will not fit 1987 and later stock aluminum heads, due to the angle of the 4 center intake manifold bolts
- Made in the U.S.A.
- Manifold height @ front: 3.50″
- Manifold height @ rear: 4.60″
- Carb pad height: 4.05″
- Port exit dimensions: 1.14″ x 1.88″
NOTE: This intake does not work with kickdown kit 491-2350U
Edelbrock 1406 Performer 600 CFM 4 Barrel Carburetor, Electric Choke
- Whether you need to replace an aging stock carb or are looking for a performance carb to top off your hot rod, this Edelbrock carb is the best choice for performance and value
CALIBRATED FOR FUEL ECONOMY
- Designed for small-block and small displacement big-block engines, this four barrel carb is recommended only for stock to Performer level applications
- Calibrated 2% leaner than #1405
- Easy to tune with great driveability
- 600 CFM
- Electric choke
- Ford/Mopar arms sold separately
- Electric choke
- Bolt-on-and-run performance right out of the box
- Smooth throttle response throughout the power band
- Lightweight all-aluminum body is compatible with gasohol and blended fuels
- Includes both timed and full vacuum ports for ignition advance
- Uses metering rods to transition between circuits – rods can be changed in seconds without carburetor removal or draining fuel
- Float levels are factory set; adjustments are rarely needed
- Change jets, adjust floats & replace needles/seats without draining fuel or removing carb
- Two-piece design means no gaskets below the fuel level for leak-free operation
Comes with:
- Metering Jets – Primary .098, Secondary .095
- Metering Rods – .075 x .047
- Step-Up Spring – yellow (4″ Hg)
Edelbrock 2102 Performer-Plus Camshaft/Lifter Kit
- Designed for Optimum Torque and Acceleration
- Maximum Performance From Idle through Mid-Range
- Matched to Edelbrock Performer Intakes
- Includes Hydraulic Lifters and Assembly Lube
- Major Improvement in Throttle Response and Torque
- Use For Daily Drivers/Trucks/Vans/RVs/4x4s
- Take The Guesswork Out Of Camshaft Selection
Edelbrock 2732 Performer Series Plate Carburetor Adapter
- Performer Series Carb Adapter plates allow proper installation of carb-to-manifold
- Mounts Square-Bore Carbs To Spread-Bore Carb Pad
- 0.93 in. Thick
- Open Center
There are no reviews yet.