Shop - Hotrod Partz

Edelbrock 5418 Small Block Chevy 3x2 3-Bolt Carb Intake Manifold

Add to cart

Edelbrock 5418 Small Block Chevy 3×2 3-Bolt Carb Intake Manifold BUY

$514.00

Add to cart

Edelbrock 7137 Pro-Flo XT RPM Intake Manifold, Pre-1986 S/B Chevy

$546.26

Add to cart

Edelbrock 71373 Pro-Flo XT EFI Intake Manifold, Small Block Chevy

$610.95

Add to cart

Edelbrock 77780 Red Roller Rocker Arm, Small Block Ford

$560.95

Add to cart

Edelbrock Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs

$284.95

Edelbrock Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs

$284.95

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347020409
Vehicle Model	Chevrolet
Series	Performer
Gasket Or Seal Included	Yes
Quantity	Kit
Availability Note	Available to Order
Warranty	12 Months
RPM Range	Idle-5500 RPM
Mounting Hole Quantity	(Carb Bolt) 4
Mounting Hole Diameter	(Carb Bolt) 5/16-18 UNC in
Angle	(Carb) 3 deg
Emissions Code
Hazardous Materials Warning	WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Manifold ht: A-3.74″, B-4.80″; Carb pad height: 4.27″; Port exit dimensions: 1.15″ x 1.87″.; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Sealant must be used on intake bolt threads if the threads extend into lifter valley or coolant passage.; NPT/Pipe thread fittings require the use of Teflon tape or paste on threads to ensure proper seal.; DO NOT OVERTIGHTEN NPT/Pipe fittings, this may cause the aluminum to crack around the fitting boss. NPT/Pipe thread is a tapered thread.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.; Will not fit under stock Corvette hood.; Even though manifolds are compatible with EGR systems, this does not mean they are legal for use on emissions controlled vehicles. Check local laws for legality.; Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Finish	Satin
Material	Aluminum
Rear Maximum Height	(B) (Measured To Engine Block) 4.80 in
Single Or Dual Plane Type	Dual

SKU: Ede/Ede
Availability:
29 in stock
Category: Manifold Intake

or View Full Info

Add to cart

Edelbrock Conversion Kit

$315.95

Edelbrock Conversion Kit

$315.95

More Information
Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347159086
Mounting Hole Quantity	11
Mounting Hole Diameter	0.331 in
Quantity	Kit
Valley Pan Included	Yes
Pulley Groove Quantity	6-Rib
Outside Pulley Diameter	3.875 in
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Length	20.25 in
Material	Cast Aluminum
Thickness	0.3 in

Availability:
15 in stock
Categories: Engine Parts, Manifold Intake

or View Full Info