Valve Covers

Add to cart

Bill Mitchell 061040 S/B Chevy Single Plane Intake Manifold

$425.99

Select options

Buy KB Ford 302 Hypereutectic Pistons, .200 Dome, 5.09 Rod

$338.99

Buy KB Ford 302 Hypereutectic Pistons, .200 Dome, 5.09 Rod

$338.99

302 Hypereutectic Pistons

Keith Black Hypereutectic pistons are T-6 heat treated and offer reduced scuffing and improved durability over stock replacement pistons. They also allow you to run tighter clearances because of reduced thermal expansion, which means more race winning power.

390 Hypereutectic alloy
Fully machined crowns and valve reliefs
Drilled oil drain backs
Full floating wrist pins
Triple wound spiral locks
Reflective alloy allows 2% power increase
Quench dome technology minimizes deterioration
Zero deck quench design
2.120″ Intake and 1.880″ Exhaust valve relief sizes

For Ford 302 c.i. (4.00″ bore x 3.00″ stroke). Use piston ring Style A (5/64″, 5/64″, 3/16″).

Item Details

C/R 64cc: 10.0, C/R 69cc: 9.4
Bore and Stroke: 4.00″ x 3.00″
Rod Length: 5.09″ Ring Style: A

SKU:
Availability:
22 in stock
Category: Valve Covers

or View Full Info

SIZE

Clear

OTB Gear 216 / 235 / 261 Water Outlet Spacer Kit

Sale

Add to cart

Buy OTB Gear 216 / 235 / 261 Water Outlet Spacer Kit

Add to cart

Buy OTB Gear Chevy Inline Six 216 / 235 / 261 Valve Cover

$349.99

OTB Gear Chevy Inline Six 235 / 261 Stud Kit

Sale

Add to cart

Buy OTB Gear Chevy Inline Six 235 / 261 Stud Kit

Sale

Add to cart

Buy OTB Gear Chevy Inline Six 235 / 261 Stud Kit (Copy)

Sale

Add to cart

Buy OTB Gear Rocket Strips of Valve Cover

Add to cart

Early Ford DUAL RESERVOIR Master Cylinder

$119.99

Add to cart

Eddie Meyer® 1949-53 Ford Flathead V8 Dual Intake Manifold

$723.99

Add to cart

Edelbrock 2101 Performer Intake Manifold Install Kit, Quadrajet

$277.99

Add to cart

Edelbrock 2121 S/B Ford 289 Intake Manifold W/O EGR, Black/Chrome

$489.56

Add to cart

Edelbrock 21813 Performer Intake Manifold, Ford 351W

$550.00

Add to cart

Edelbrock 7137 Pro-Flo XT RPM Intake Manifold, Pre-1986 S/B Chevy

$546.26

Add to cart

Edelbrock 71373 Pro-Flo XT EFI Intake Manifold, Small Block Chevy

$610.95

Add to cart

Edelbrock Supercharger Aluminum Coil Covers #41113 For 2005-10 Chrysler HEMI

$481.95

Edelbrock Supercharger Aluminum Coil Covers #41113 For 2005-10 Chrysler HEMI

$481.95

More Information
Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411139
Quantity	Kit
Attachment Type	Bolt-On
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Depending on your application, there will be two different factory valve cover bushings
Color	Black
Finish	Black Powder Coated
Material	Cast Aluminum
Universal Or Specific Fit	Specific

Availability:
12 in stock
Category: Valve Covers

or View Full Info

Add to cart

Edelbrock Supercharger Aluminum Coil Covers #41123 For 2005-13 Corvette

$501.95

Edelbrock Supercharger Aluminum Coil Covers #41123 For 2005-13 Corvette

$501.95

More Information
Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411238
Quantity	Kit
Attachment Type	Bolt-On
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Depending on your application, there will be two different factory valve cover bushings
Color	Black
Finish	Black Powder Coated
Material	Cast Aluminum
Universal Or Specific Fit	Specific

SKU: Supercharger
Availability:
25 in stock
Category: Valve Covers

or View Full Info

Add to cart

Edelbrock Supercharger Aluminum Coil Covers #41124 For 2014-19 Corvette

$446.95

Edelbrock Supercharger Aluminum Coil Covers #41124 For 2014-19 Corvette

$446.95

More Information
Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411245
Quantity	Kit
Attachment Type	Bolt-On
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Depending on your application, there will be two different factory valve cover bushings: a 5/8″ diameter and a 7/8″ diameter. The 5/8″ diameter bushings will install onto the supplied hex coil cover supports using the spacers from bag #6. The 7/8″ diameter bushings will use the washers from bag #6.
Color	Red
Finish	Red Powder Coated
Material	Cast Aluminum
Universal Or Specific Fit	Specific

SKU: Sup/Sup/Sup/Sup
Availability:
15 in stock
Category: Valve Covers

or View Full Info

Add to cart

Edelbrock Supercharger Aluminum Coil Covers #41133 For 2005-10 Mustang GT 4.6L

$350.00

Edelbrock Supercharger Aluminum Coil Covers #41133 For 2005-10 Mustang GT 4.6L

$350.00

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411337
Quantity	Kit
Attachment Type	Bolt-On
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Depending on your application, there will be two different factory valve cover bushings: a 5/8″ diameter and a 7/8″ diameter. The 5/8″ diameter bushings will install onto the supplied hex coil cover supports using the spacers from bag #6. The 7/8″ diameter bushings will use the washers from bag #6.
Color	Black
Finish	Black Powder Coated
Material	Cast Aluminum
Universal Or Specific Fit	Specific

SKU: Coil
Availability:
19 in stock
Category: Valve Covers
Tags: classic fordhotrod, hotrods, Old Timers

or View Full Info

Add to cart

Edelbrock Supercharger Aluminum Coil Covers #41142 For 2010-13 Camaro SS

$572.95

Edelbrock Supercharger Aluminum Coil Covers #41142 For 2010-13 Camaro SS

$572.95

More Information
Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411429
Quantity	Set of 2
Attachment Type	Bolt-On
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Depending on your application, there will be two different factory valve cover bushings: a 5/8″ diameter and a 7/8″ diameter. The 5/8″ diameter bushings will install onto the supplied hex coil cover supports using the spacers from bag #6. The 7/8″ diameter bushings will use the washers from bag #6.
Color	Red / Black
Finish	Black And Red Powder Coated
Material	Aluminum
Universal Or Specific Fit	Specific

SKU: C/C/C/C
Availability:
17 in stock
Category: Valve Covers

or View Full Info

Add to cart

Edelbrock Supercharger Coil Covers #41103, 10-13 Corvette GS W/ Dry Sump/Z06

$467.95

Edelbrock Supercharger Coil Covers #41103, 10-13 Corvette GS W/ Dry Sump/Z06

$467.95

More Information
Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411030
Quantity	Kit
Attachment Type	Bolt-On
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Depending on your application, there will be two different factory valve cover bushings: a 5/8″ diameter and a 7/8″ diameter. The 5/8″ diameter bushings will install onto the supplied hex coil cover supports using the spacers from bag #6. The 7/8″ diameter bushings will use the washers from bag #6.
Color	Black
Finish	Black Powder Coated
Material	Cast Aluminum
Universal Or Specific Fit	Specific

SKU: Corvette
Availability:
17 in stock
Category: Valve Covers

or View Full Info

Add to cart

Edelbrock Supercharger Coil Covers #41139, 15-19 Chrysler HEMI W/DP-3C SC System

$549.95

Edelbrock Supercharger Coil Covers #41139, 15-19 Chrysler HEMI W/DP-3C SC System

$549.95

More Information
Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411399
Quantity	Kit
Attachment Type	Bolt-On
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Depending on your application, there will be two different factory valve cover bushings
Color	Black
Finish	Black Powder Coated
Material	Cast Aluminum
Universal Or Specific Fit	Specific

SKU: Ed/Ed/Ed/Ed/2
Availability:
20 in stock
Category: Valve Covers

or View Full Info

Add to cart

Edelbrock Supercharger Coil Covers #41143 For 10-15 Camaro SS W/Low Profile Top

$459.95

Edelbrock Supercharger Coil Covers #41143 For 10-15 Camaro SS W/Low Profile Top

$459.95

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411436
Quantity	Kit
Attachment Type	Bolt-On
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Depending on your application, there will be two different factory valve cover bushings
Color	Black
Finish	Black Powder Coated
Material	Cast Aluminum
Universal Or Specific Fit	Specific

SKU: Edelbrock
Availability:
12 in stock
Category: Valve Covers

or View Full Info

Add to cart

Edelbrock Supercharger Top & Coil Covers #41144 For 2010-13 Chevy Camaro SS

$9,017.95

Edelbrock Supercharger Top & Coil Covers #41144 For 2010-13 Chevy Camaro SS

$9,017.95

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411443
Quantity	Kit
Attachment Type	Bolt-On
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Removal of the supercharger is required to properly install the new Edelbrock supercharger lid and coil cover upgrade kit; This can be done by removing the supercharger belt, air intake, disconnecting all hoses and electrical connectors from the supercharger and unbolting the supercharger from the engine; NOTE: For more specific details, reverse the installation procedure. The installation procedure specific for your application can be found at: http://www.edelbrock.com/automotive/misc/tech-enter/install/1000/1597.pdf; With the supercharger removed, use a 5mm Hex to remove fourteen (14) bolts securing the lid to the supercharger manifold; Remove the lid to manifold gasket and clean the mating surfaces. Install the supplied gasket and position the new supercharger lid onto the manifold; Using the factory bolts, secure the lid to the manifold. Torque all bolts to 8 ft-lbs.; NOTE: While the supercharger is out, it may be a good idea to change the oil in the supercharger. This will eliminate the need to remove the supercharger again when service is due. Please note that the recommended service interval is 100,000 supercharged miles. If your supercharger is relatively new with low millage, the service procedure can be skipped at this time. The supercharger service procedure can be found here: http://www.edelbrock.com/automotive/mc/superchargers/pdf/service-procedure.pdf; Reinstall the manifold, supercharger belt, air intake, hoses and electrical connectors; Install the supplied retainer studs onto the coil covers and securely position the coil covers onto the engine; Top off all fluid as needed. Turn key on and verify there are no leaks. Repair any leaks before operating the vehicle.
Color	Red / Black
Finish	Black And Red Powder Coated
Material	Cast Aluminum
Universal Or Specific Fit	Specific

SKU: Ed/Ed/Ed/Ed
Availability:
29 in stock
Category: Valve Covers

or View Full Info

Add to cart

EMD – RIBSTER ROCKER BOX COVERS – HARLEY BIG TWIN EVOLUTION 1984-1999 – BLACK

$365.99

EMD – RIBSTER ROCKER BOX COVERS – HARLEY BIG TWIN EVOLUTION 1984-1999 – BLACK

$365.99

EMD – RIBSTER ROCKER BOX COVERS – HARLEY BIG TWIN EVOLUTION 1984-1999 – BLACK

The Estevez Ribster ribbed rocker box covers have a unique ribbed design that is directly inspired by early HD flathead cylinders and will give your bike a completely different look. Designed to fit all Harley Davidson Big Twin Evolution motors from 1984-1999.

Manufactured in die cast aluminum with CNC milled gasket surface
Mounts in place of stock rocker box cover using stock hardware and gaskets (not included)
Sold in pairs
Made in France

Fitment:

YEAR	MAKE	MODEL
1985	Harley-Davidson	80 Fat Bob – FXEF
1985	Harley-Davidson	80 Low Rider – FXSB
1984	Harley-Davidson	Disc Glide – FXRDG
1994 – 1998	Harley-Davidson	Dyna Convertible – FXDS-CONV
1991 – 1992	Harley-Davidson	Dyna Daytona – FXDB
1992	Harley-Davidson	Dyna Glide Custom

Availability:
44 in stock
Category: Valve Covers

or View Full Info

Select options

FiTech 30065 Go EFI 2X4, 1200HP Power Adder, Bright Aluminum

$2,136.00

FiTech 30065 Go EFI 2X4, 1200HP Power Adder, Bright Aluminum

$2,136.00

SKU:
Availability:
19 in stock
Categories: Engine Parts, Valve Covers

or View Full Info

Your Vehicles

Clear

FiTech 30258 Go Port EFI Fuel Injection System, BBC, Black

Add to cart

LS Series Coil Covers in Black Finish (3-3/8″ Overall Height)

$404.95

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411832
Series	LS Series
Attachment Type	Stretch
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Note: These covers are intended for custom hot rod applications. As such, they may not clear all the hoses, emission hardware,; and/or accessories found in a stock application. Modification of the covers may be necessary for use in such an application.; 1.Disconnect and remove the spark plug wires and set them aside for reinstallation later, then detach the wiring harness connector.; Unbolt and remove the bracket with the coils attached. At this time, test fit the coil covers on the engine to ensure they will fit; your application without interference.; 2. Once the fit has been verified, separate the wiring loom enough to disconnect the small clips securing it to the bracket, then; remove the individual coils from the bracket. The stock coil mounting bracket can be set aside or discarded as it will not be; reused. Mount the ignition coils to the underside of the covers using the stock bolts, carefully routing the wires so as to prevent them from being pinched or damaged.; 3. Attach the supplied reusable tie wrap to the center provision on the underside of the coil cover using the supplied #6 cap screw.; Use the tie wrap to secure the wiring harness connector to the cover, then install the spark plug wires onto the ignition coils.; The coil cover can then be secured by threading the supplied bolts into the mounting holes of the valve cover. Use a dummy; bolt secured with a nut to fill any mounting holes in the coil cover that do not correspond with a threaded boss in the valve cover.; 4. Attach the ignition wires to the spark plugs and your installation is complete. Installation is the same for both sides of the engine,; but be aware that the engine oil dipstick tube may need to be bent outward slightly to clear the passenger side cover.
Color	Black
Finish	Black Powder Coated
Material	Aluminum
Universal Or Specific Fit	Specific

SKU: Covers LSS/LSS
Availability:
10 in stock
Category: Valve Covers

or View Full Info

Add to cart

LS Series Coil Covers in Polished Finish (3-3/8″ Overall Height)

$468.95

LS Series Coil Covers in Polished Finish (3-3/8″ Overall Height)

$468.95

Manufacturer	Edelbrock
Application	Application Specific
UPC	00085347411818
Series	LS Series
Attachment Type	Stretch
Availability Note	Available to Order
Warranty	12 Months
Emissions Code	N/A
Hazardous Materials Warning	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes	Note: These covers are intended for custom hot rod applications. As such, they may not clear all the hoses, emission hardware,; and/or accessories found in a stock application. Modification of the covers may be necessary for use in such an application.; 1.Disconnect and remove the spark plug wires and set them aside for reinstallation later, then detach the wiring harness connector.; Unbolt and remove the bracket with the coils attached. At this time, test fit the coil covers on the engine to ensure they will fit; your application without interference.; 2. Once the fit has been verified, separate the wiring loom enough to disconnect the small clips securing it to the bracket, then; remove the individual coils from the bracket. The stock coil mounting bracket can be set aside or discarded as it will not be; reused. Mount the ignition coils to the underside of the covers using the stock bolts, carefully routing the wires so as to prevent them from being pinched or damaged.; 3. Attach the supplied reusable tie wrap to the center provision on the underside of the coil cover using the supplied #6 cap screw.; Use the tie wrap to secure the wiring harness connector to the cover, then install the spark plug wires onto the ignition coils.; The coil cover can then be secured by threading the supplied bolts into the mounting holes of the valve cover. Use a dummy; bolt secured with a nut to fill any mounting holes in the coil cover that do not correspond with a threaded boss in the valve cover.; 4. Attach the ignition wires to the spark plugs and your installation is complete. Installation is the same for both sides of the engine,; but be aware that the engine oil dipstick tube may need to be bent outward slightly to clear the passenger side cover.
Color	Polished
Material	Aluminum
Universal Or Specific Fit	Specific

SKU: Covers
Availability:
20 in stock
Category: Valve Covers

or View Full Info

MFG. Part #	21813
Brand	Edelbrock
Intake Manifold Type	Dual Plane
RPM Range	Idle-5,500
Material Type	Aluminum

Bill Mitchell 061040 S/B Chevy Single Plane Intake Manifold

Buy KB Ford 302 Hypereutectic Pistons, .200 Dome, 5.09 Rod

302 Hypereutectic Pistons

Item Details

Buy OTB Gear 216 / 235 / 261 Water Outlet Spacer Kit

Buy OTB Gear Chevy Inline Six 216 / 235 / 261 Valve Cover

Buy OTB Gear Chevy Inline Six 235 / 261 Stud Kit

Buy OTB Gear Chevy Inline Six 235 / 261 Stud Kit (Copy)

Buy OTB Gear Rocket Strips of Valve Cover

Early Ford DUAL RESERVOIR Master Cylinder

Eddie Meyer® 1949-53 Ford Flathead V8 Dual Intake Manifold

Edelbrock 2101 Performer Intake Manifold Install Kit, Quadrajet

Edelbrock 2121 S/B Ford 289 Intake Manifold W/O EGR, Black/Chrome

Edelbrock 21813 Performer Intake Manifold, Ford 351W

Edelbrock 7137 Pro-Flo XT RPM Intake Manifold, Pre-1986 S/B Chevy

Edelbrock 71373 Pro-Flo XT EFI Intake Manifold, Small Block Chevy

Edelbrock Supercharger Aluminum Coil Covers #41113 For 2005-10 Chrysler HEMI

Edelbrock Supercharger Aluminum Coil Covers #41123 For 2005-13 Corvette

Edelbrock Supercharger Aluminum Coil Covers #41124 For 2014-19 Corvette

Edelbrock Supercharger Aluminum Coil Covers #41133 For 2005-10 Mustang GT 4.6L

Edelbrock Supercharger Aluminum Coil Covers #41142 For 2010-13 Camaro SS

Edelbrock Supercharger Coil Covers #41103, 10-13 Corvette GS W/ Dry Sump/Z06

Edelbrock Supercharger Coil Covers #41139, 15-19 Chrysler HEMI W/DP-3C SC System

Edelbrock Supercharger Coil Covers #41143 For 10-15 Camaro SS W/Low Profile Top

Edelbrock Supercharger Top & Coil Covers #41144 For 2010-13 Chevy Camaro SS

EMD – RIBSTER ROCKER BOX COVERS – HARLEY BIG TWIN EVOLUTION 1984-1999 – BLACK

FiTech 30065 Go EFI 2X4, 1200HP Power Adder, Bright Aluminum

FiTech 30258 Go Port EFI Fuel Injection System, BBC, Black

Holley 300-214 Hi-Ram Lower Manifold, LS3/L92, EFI

Holley 7223 Dual Quad Enderle Style Air Scoop

Holley Mid-Rise EFI Intake Manifold & Rail Kit, LS1

Holley Sniper 820051 EFI Sheet Metal Intake Manifold, LS1/LS2/LS6

LS Series Coil Covers in Black Finish (3-3/8″ Overall Height)

LS Series Coil Covers in Polished Finish (3-3/8″ Overall Height)

Contact Information

Contact Information